Contact Platform Support
Help CenterPolyester Self Adhesive Modified Bituminous Waterproof Membrane
Related Products
-
Self Adhesive Modified Bituminous Waterproof MembraneUS$ 3 - 5.5MOQ: 10 Square Meters -
Self Adhesive Modified Bituminous Waterproof MembraneUS$ 2 - 3MOQ: 10 Square Meters
-
Self Adhesive Modified Bitumen Waterproofing Membrane UnderlaymentUS$ 2 - 3MOQ: 50 Square Meters
-
Non-asphalt Polymer Waterproofing Membrane UnderlaymentUS$ 4 - 6MOQ: 40 Square Meters
-
Pet Aluminum Bitumen Self-adhesive Waterproofing MembraneUS$ 2 - 3MOQ: 10 Square Meters
1. Tackifying resin provides the membrane with strong adhesive strength which could make membranes stick to the base surface tightly.
2. The membrane has good puncture resistant, tear resistant and abrasive resistant property with the polyester as its reinforcement.
3. The membranes can be self healing for tiny cracks caused by environment.
4. Long-time stickiness assures no fall-off or any leakage between the membrane and the base surface.
5. The membrane has high tensile strength and good elongation property, it can maintain its shape even in the case of cracks and deformation on the base surface.
6. No dripping at high temperature and no cracks at low temperature.
7. Excellent chemical resistance, corrosion resistance and weathering resistance.
1, Interior roofs and underground construction.
2, Subways, tunnels, pools and water canals.
3, Waterproof projects which fire is not allow to be used.
4, Excellent for cold region due to its good low temperature flexibility.
Performance Standard GB 23441-2009 TYPE PY
| Item | Index | |||
| Ι | ΙΙ | |||
| The Content of Soluble Substance (g/m2) | 2.0mm | 130 | ||
| 3.0mm | 2100 | |||
| 4.0mm | 2900 | |||
| Tensile Strength | Tension N/50mm≥ | 2.0mm | 350 | |
| 3.0mm | 450 | 600 | ||
| 4.0mm | 450 | 800 | ||
| The maximum tension rate/%≥ | 30 | 40 | ||
| Heat Resistance | 70 ℃,no slipping, no dripping and no fall-off | |||
| Low Temperature Flexibility/℃ | -20 | -30 | ||
| No Crack | ||||
| Water Impermeability | 0.3MPa 120min impermeability | |||
| Peel Strength N/mm≥ | Peel strength with the membrane | 1.0 | ||
| Peel strength witht the aluminum sheet | 1.5 | |||
| Water tightness | Pass | |||
| Oil permeability (the number of sheets)≤ | 2 | |||
| Holding Power min≥ | 15 |
|||
1, The base surface must be checked and cleaned before paving in order to make it firm, clean and flat without any dust, oil and cracks.
2, Brush primer on the base surface evenly before paving.
3, Use blowtorch to help paving the parts which are hard to stick.
4, After the primer dry, pave the membrane from lower to higher. During the paving, fix one end of the membrane, and remove the isolation film, then pave it according to the line.
5, Vertical surface: stick membranes and the surface/membranes completely. For paving the end of membranes on the vertical surface, fix the end first, then seal it with membrane sealant or seal the end in the wall groove.
Send Inquiry to This Supplier
You May Also Like
-
High Adhesive, Water-proof, Anti Corrosion, Weather-resistant Asphalt Adhesive Glue Patch Cover for ConstructionNegotiableMOQ: 100 Rolls
-
2.0mm Textured HDPE Geomembrane Dual-Sided Friction for Slope ProtectionUS$ 9.5 - 10MOQ: 100 Square Meters
-
GeomembraneNegotiableMOQ: 2700 Rolls
-
Non-curable Rubber Paint Rubber Asphalt Waterproof Coating Made in ChinaUS$ 1.5 - 6MOQ: 500 Kilograms
-
Low Cost Waterproof Material ManufactureUS$ 1,000 - 50,000MOQ: 1 Set
-
PTFE Architectural Membrane MaterialNegotiableMOQ: 1
-
Special Compound BaseUS$ 0.12 - 0.25MOQ: 7000 Square Meters
-
PolyLock/HDPE Lock/ E Lock/ HDPE E Lock/Geomembrane Attaches HDPE GeomembranesUS$ 10 - 50MOQ: 1 Piece
-
Breathable House Wrap Membrane Roofing Waterproofing MembraneUS$ 0.42 - 0.42MOQ: 5000 Square Meters
-
<MIicroVENT> Waterproof Vent MembraneUS$ 0.1 - 3MOQ: 10000 Pieces
