Hot Dip Galvanized Steel Grille Roof -ISO9001 20YEARS Factory
Specifications
1. steel grille roof2. tenstile &corrosion
3.beautiful surface
4.hot dipped galvanized
steel grille roof --
steel grille roof is made of steel grating manufactured as interior ceiling products . Steel grating products as ceiling surface after hot galvanized, with 30 years of rust , maintenance-free characteristics. Its structure , lightweight, practical people on the ceiling, central air conditioning and other equipment to facilitate maintenance .

|
steel grille roof Detail Information
| ||||||||||||||
| ||||||||||||||
| ||||||||||||||
Additional Information- ISO 9001 grating platform manufacturer grating ceiling | ||||||||||||||
|
steel grille roof can be widely used in the printing shop , industrial plants , exhibition center, a large gymnasium , commercial exhibition , railway stations, docks, airports and other commercial and industrial buildings ceiling . Steel grating ceiling is a certain carrying capacity and has a decorative steel grating products , generally use ordinary Q235 low carbon flat steel , stainless steel, brass, aluminum was slotted ( hole ) , plug , welding, fine made of whole processes . Its solid solder joint , pitch uniform , flat surface . It can be said that industrial products and arts and crafts .
steel grille roof
1, high strength steel grating ceiling with a light structure, strong bonding grid structure so that it has a high load , the structure is light , easy to hang unloading , installation and other features .
2 , steel grating as a ceiling use, with beautiful appearance, durable : hot-dip zinc surface treatment so that it has very good corrosion resistance , surface gloss appearance.
3 , the use of this product has good ventilation, lighting , heat , explosion-proof, anti-slip properties.
4 easy to use as a ceiling self-cleaning , easy to maintain. Long service life.Fixed steel grating ceiling there are two methods of welding and installation . Without dismantling of permanent , can be welded , it is welded to the supports. Specific location on each corner of the board of the first root of flat steel, weld length of not less than 20 mm , height of not less than 3 mm of fillet weld adopts mounting clips without damaging the zinc layer has the advantage of convenience and disassembly , use mounting clamps , each plate should be used at least four mounting clips for larger plate on the best available support complex multi install several .
Send Inquiry to This Supplier
You May Also Like
-
Cast Iron Trench Drain Cover, 1/2" Thick, Load Class E600, 24"x12" Solid Grate for Industrial UseNegotiableMOQ: 300 Square Meters
-
HPL Panel (clean Room)NegotiableMOQ: 100 Square Meters
-
Corrugated Metal Cladding Panel 0.7mm Zincalume Steel for Roof and Wall SystemsNegotiableMOQ: 1 Square Meter
-
HRC Hot Rolled Carbon Steel Coil Q235 SS400 Q345 SA302 Modern Durable Mid Hard Custom LengthNegotiableMOQ: 1 Ton
-
Welded Steel Grating Standard Compliant ASTM A36 1.5m x 6m Sheets With 40x40mm MeshNegotiableMOQ: 50 Cubic Centimeters
-
SOURCE POLYURETHANE SANDWICH PANEL FactoryNegotiableMOQ: 100 Pieces
-
Hot Dipped Galvanized Diamond Metal Lath Expanded 2-1/2-gauge Steel Sheet Anti-Corrosion Durable Low Cost Roofing Wall FloorUS$ 1.7 - 3.2MOQ: 1 Piece
-
High Purity Zirconia Ceramic Ring 8mm OD With 1500 MPa Flexural Strength for Valve SealsNegotiableMOQ: 1 Piece
-
Sandwich PanelNegotiableMOQ: 2500 Pieces
-
pu Wall Sandwich Panel Rigid Insulation Polyurethane Foam BoardNegotiableMOQ: 1













